やっときましたーーー。
待ち焦れてたよ i.MX6 Dual !! ということでさっそく Boot してみた。
U-Boot 2009.08-dirty (Jan 30 2013 - 16:37:43) CPU: Freescale i.MX6 family TO1.1 at 792 MHz Temperature: 43 C, calibration data 0x59b52e5f mx6q pll1: 792MHz mx6q pll2: 528MHz mx6q pll3: 480MHz mx6q pll8: 50MHz ipg clock : 66000000Hz ipg per clock : 66000000Hz uart clock : 80000000Hz cspi clock : 60000000Hz ahb clock : 132000000Hz axi clock : 198000000Hz emi_slow clock: 22000000Hz ddr clock : 396000000Hz usdhc1 clock : 198000000Hz usdhc2 clock : 198000000Hz usdhc3 clock : 198000000Hz usdhc4 clock : 198000000Hz nfc clock : 24000000Hz Board: i.MX6DL/Solo-WandBoard: unknown-board Board: 0x61011 [POR ] Boot Device: SD DRAM: 1 GB MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2 In: serial Out: serial Err: serial Gotr MAC = 00:1F:7B:B2:00:69 Net: got MAC address from IIM: 00:1f:7b:b2:00:69 FEC0 Hit any key to stop autoboot: 0 WANDBOARD U-Boot >ふむ、 u-boot が立ち上がるのね。 よしよし。 とりあえず Linux の dmesg を
mmc2 is current device MMC read: dev # 2, block # 2048, count 16384 ... 16384 blocks read: OK ## Booting kernel from Legacy Image at 10800000 ... Image Name: Linux-3.0.35+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1783944 Bytes = 1.7 MB Load Address: 10008000 Entry Point: 10008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Linux version 3.0.35+ (tapani@triceratops) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #176 SMP PREEMPT Thu Feb 7 19:38:10 CST 2013 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Wandboard [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] CPU identified as i.MX6DL/SOLO, silicon rev 1.1 [ 0.000000] PERCPU: Embedded 7 pages/cpu @80cf5000 s5024 r8192 d15456 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 206848 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p1 rootwait rw video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 80MB 736MB = 816MB total [ 0.000000] Memory: 821464k/821464k available, 227112k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xfbe00000 - 0xffe00000 ( 64 MB) [ 0.000000] vmalloc : 0xc0800000 - 0xf2000000 ( 792 MB) [ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB) [ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB) [ 0.000000] .init : 0x80008000 - 0x8002d000 ( 148 kB) [ 0.000000] .text : 0x8002d000 - 0x8049b000 (4536 kB) [ 0.000000] .data : 0x8049c000 - 0x804d3800 ( 222 kB) [ 0.000000] .bss : 0x804d3824 - 0x804ede38 ( 106 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Verbose stalled-CPUs detection is disabled. [ 0.000000] NR_IRQS:496 [ 0.000000] MXC GPIO hardware [ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms [ 0.000000] Set periph_clk's parent to pll2_pfd_400M! [ 0.000000] arm_max_freq=2 [ 0.000000] MXC_Early serial console at MMIO 0x2020000 (options '115200') [ 0.000000] bootconsole [ttymxc0] enabled [ 0.000000] Console: colour dummy device 80x30 [ 0.222635] Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280) [ 0.310971] pid_max: default: 32768 minimum: 301 [ 0.315836] Mount-cache hash table entries: 512 [ 0.321050] CPU: Testing write buffer coherency: ok [ 0.426839] CPU1: Booted secondary processor [ 0.516256] Brought up 2 CPUs [ 0.523516] SMP: Total of 2 processors activated (3162.11 BogoMIPS). [ 0.530317] devtmpfs: initialized [ 0.551642] print_constraints: dummy: [ 0.555629] NET: Registered protocol family 16 [ 0.564617] print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal [ 0.572270] print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal [ 0.580103] print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal [ 0.587816] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal [ 0.595598] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal [ 0.603303] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal [ 0.690943] L310 cache controller enabled [ 0.694978] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02050000, Cache size: 524288 B [ 0.722117] bio: create slabat 0 [ 0.727074] print_constraints: VDDA: 2500 mV [ 0.731661] print_constraints: VDDIO: 3300 mV [ 0.737144] SCSI subsystem initialized [ 0.741397] spi_imx imx6q-ecspi.0: probed [ 0.745672] spi_imx imx6q-ecspi.1: probed [ 0.750466] usbcore: registered new interface driver usbfs [ 0.756116] usbcore: registered new interface driver hub [ 0.761671] usbcore: registered new device driver usb [ 0.786244] imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [ 0.794471] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.801765] Bluetooth: Core ver 2.16 [ 0.805480] NET: Registered protocol family 31 [ 0.809955] Bluetooth: HCI device and connection manager initialized [ 0.816343] Bluetooth: HCI socket layer initialized [ 0.821238] Bluetooth: L2CAP socket layer initialized [ 0.826332] Bluetooth: SCO socket layer initialized [ 0.831691] cfg80211: Calling CRDA to update world regulatory domain [ 0.838531] Switching to clocksource mxc_timer1 [ 0.858128] NET: Registered protocol family 2 [ 0.862705] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.870577] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.880574] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 0.888551] TCP: Hash tables configured (established 131072 bind 65536) [ 0.895197] TCP reno registered [ 0.898356] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.904332] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.911050] NET: Registered protocol family 1 [ 0.915553] _regulator_get: etb supply vcore not found, using dummy regulator [ 0.923267] _regulator_get: etm.0 supply vcore not found, using dummy regulator [ 0.930678] _regulator_get: etm.1 supply vcore not found, using dummy regulator [ 0.938375] Static Power Management for Freescale i.MX6 [ 0.943633] wait mode is disabled for i.MX6 [ 0.948007] cpaddr = c0820000 suspend_iram_base=c08ac000 [ 0.953434] PM driver module loaded [ 0.957151] IMX usb wakeup probe [ 0.960878] IMX usb wakeup probe [ 0.964561] cpu regulator init ldo=0 [ 0.968294] i.MXC CPU frequency driver [ 0.990147] msgmni has been set to 1604 [ 0.994286] io scheduler noop registered [ 0.998275] io scheduler cfq registered (default) [ 1.004280] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi [ 1.010775] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0x1a:0xa0:0xc1 [ 1.017784] fbcvt: 1920x1080@60: CVT Name - 2.073M9 [ 1.053182] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7) [ 1.139335] Console: switching to colour frame buffer device 240x67 [ 1.176490] imx-sdma imx-sdma: loaded firmware 1.1 [ 1.185517] imx-sdma imx-sdma: initialized [ 1.189995] Serial: IMX driver [ 1.193255] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX [ 1.199755] console [ttymxc0] enabled, bootconsole disabled [ 1.199755] console [ttymxc0] enabled, bootconsole disabled [ 1.211259] imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX [ 1.218424] [drm] Initialized drm 1.1.0 20060810 [ 1.223669] [drm] Initialized vivante 1.0.0 20120216 on minor 0 [ 1.230301] FEC Ethernet Driver [ 1.234700] fec_enet_mii_bus: probed [ 1.239285] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.245972] add wake up source irq 72 [ 1.249691] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller [ 1.256441] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 1 [ 1.273412] fbcvt: 1920x1080@60: CVT Name - 2.073M9 [ 1.293301] fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200 [ 1.313127] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 [ 1.313854] hub 1-0:1.0: USB hub found [ 1.313875] hub 1-0:1.0: 1 port detected [ 1.314138] add wake up source irq 75 [ 1.317184] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller [ 1.317221] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 2 [ 1.343142] fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000 [ 1.363241] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 [ 1.364547] hub 2-0:1.0: USB hub found [ 1.364586] hub 2-0:1.0: 1 port detected [ 1.365147] Initializing USB Mass Storage driver... [ 1.365537] usbcore: registered new interface driver usb-storage [ 1.365556] USB Mass Storage support registered. [ 1.365572] ARC USBOTG Device Controller driver (1 August 2005) [ 1.365720] udc: request mem region for fsl-usb2-udc failed [ 1.365754] fsl-usb2-udc: probe of fsl-usb2-udc failed with error -16 [ 1.366490] mousedev: PS/2 mouse device common for all mice [ 1.366511] i2c /dev entries driver [ 1.367945] Linux media interface: v0.10 [ 1.368212] Linux video capture interface: v2.00 [ 1.368971] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16 [ 1.369397] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17 [ 1.369686] Bluetooth: HCI UART driver ver 2.2 [ 1.369708] Bluetooth: HCI H4 protocol initialized [ 1.369803] cpuidle: using governor ladder [ 1.369820] cpuidle: using governor menu [ 1.370073] sdhci: Secure Digital Host Controller Interface driver [ 1.370093] sdhci: Copyright(c) Pierre Ossman [ 1.370349] _regulator_get: sdhci-esdhc-imx.2 supply vmmc not found, using dummy regulator [ 1.370903] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA [ 1.371034] sdhci sdhci-esdhc-imx.1: no write-protect pin available! [ 1.371056] sdhci sdhci-esdhc-imx.1: no card-detect pin available! [ 1.372114] _regulator_get: sdhci-esdhc-imx.1 supply vmmc not found, using dummy regulator [ 1.384286] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.1] using ADMA [ 1.384414] sdhci sdhci-esdhc-imx.0: no write-protect pin available! [ 1.385493] _regulator_get: sdhci-esdhc-imx.0 supply vmmc not found, using dummy regulator [ 1.388491] mmc2: SDHCI controller on platform [sdhci-esdhc-imx.0] using ADMA [ 1.390299] VPU initialized [ 1.391801] mxc_asrc registered [ 1.429139] Thermal calibration data is 0x59b52e5f [ 1.664771] Anatop Thermal registered as thermal_zone0 [ 1.670167] anatop_thermal_probe: default cooling device is cpufreq! [ 1.677529] usbcore: registered new interface driver usbhid [ 1.677537] usbhid: USB HID core driver [ 1.677545] zram: num_devices not specified. Using default: 1 [ 1.677553] zram: Creating 1 devices ... [ 1.678781] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio [ 1.678927] mxc_spdif mxc_spdif.0: MXC SPDIF Audio [ 1.680980] _regulator_get: 1-000a supply VDDD not found, using dummy regulator [ 1.681292] sgtl5000 1-000a: sgtl5000 revision 17 [ 1.681493] print_constraints: 1-000a: 850 <--> 1600 mV at 1200 mV normal [ 1.702783] asoc: sgtl5000 <-> imx-ssi.1 mapping ok [ 1.707534] asoc: mxc-spdif <-> imx-spdif-dai.0 mapping ok [ 1.717435] asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok [ 1.724132] mmc0: new high speed SDHC card at address 0002 [ 1.724644] ALSA device list: [ 1.724651] #0: sgtl5000-audio [ 1.724657] mmcblk0: mmc0:0002 00000 3.70 GiB [ 1.724664] #1: imx-spdif [ 1.724669] #2: imx-hdmi-soc [ 1.725241] TCP cubic registered [ 1.725251] NET: Registered protocol family 17 [ 1.725357] Bluetooth: RFCOMM socket layer initialized [ 1.725366] Bluetooth: RFCOMM ver 1.11 [ 1.725374] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.725380] Bluetooth: BNEP filters: multicast [ 1.725388] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.725542] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.725928] Bus freq driver module loaded [ 1.725938] Bus freq driver Enabled [ 1.725998] mxc_dvfs_core_probe [ 1.726167] DVFS driver module loaded [ 1.726241] mmcblk0: p1 p2 [ 1.726394] mmcblk0: p2 size 3072000 extends beyond EOD, truncated [ 1.941941] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities [ 1.991755] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities [ 2.204843] mmc1: queuing unknown CIS tuple 0x80 (50 bytes) [ 2.315494] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 2.354229] mmc1: queuing unknown CIS tuple 0x80 (4 bytes) [ 2.726218] mmc1: queuing unknown CIS tuple 0x02 (1 bytes) [ 2.766960] mmc1: new SDIO card at address 0001 [ 6.443938] EXT4-fs (mmcblk0p1): 12 orphan inodes deleted [ 6.449342] EXT4-fs (mmcblk0p1): recovery complete [ 7.799951] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 7.808098] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 7.831855] devtmpfs: mounted [ 7.834988] Freeing init memory: 148K [ 10.899471] init: mounted-proc main process (654) terminated with status 1 mountall: Event failed speech-dispatcher disabled; edit /etc/default/speech-dispatcher Checking for running unattended-upgrades: Last login: Thu Jan 1 00:00:54 UTC 1970 on tty1 Welcome to Linaro 11.10 (development branch) (GNU/Linux 3.0.35+ armv7l) * Documentation: https://wiki.linaro.org/ New release '12.04 LTS' available. Run 'do-release-upgrade' to upgrade to it. root@wandboard:~# * Starting bluetooth [ OK ] * PulseAudio configured for per-user sessions saned disabled; edit /etc/default/saned Device setup complete Setting up swapspace version 1, size = 244140 KiB Error resolving 1.pool.ntp.org: No address associated with hostname (-5) no label, UUID=242a0bda-9ea7-4550-8102-0a123563ce1d 1 Jan 00:00:56 ntpdate[1717]: Can't find host 1.pool.ntp.org: No address associated with hostname (-5) 1 Jan 00:00:56 ntpdate[1717]: no servers can be used, exiting Setting up swapspace version 1, size = 1415164 KiB no label, UUID=1b7e40fc-cac7-442d-99ea-b715e1df827f root@wandboard:~#
ふむふむ、なんかすぐ NetBSD 動く気がしてきた!!
0 件のコメント:
コメントを投稿